Search Results

Honda's technology applied to CR-Z HEV propulsion system. Presenter Takeo Nishibori, Honda R&D Co., Ltd.

An overview of Daimler?s progression to advance powertrain technology in a growth industry shows many different solutions to improvement in transportation. Daimler continues to make breakthroughs in technology development and application building on 125 years of automotive development. Optimization of current powertrains will enable a significant gain in CO2/mi reductions, that dependent on product mix can be augmented with additional technologies. There is however no bypass to some form of electrification, enabling efficiency gains and alternative forms of power supply. Development of hybrid powertrains continues in an established manner and enhanced development of further electrified powertrains are in development. Organizationally and technically, significant skills and adjustments need to continue to be undertaken enabling OEMs and in particular the supply base to develop optimized solutions efficiently. The outlook is bright for novel component development and innovation.

The introduction of hybrid and plug-in hybrid electric vehicles has resulted in the introduction of battery systems into the realm of OBD II diagnostics. After a high-level overview of battery systems, general battery system fault responses are discussed, as well as which of these might be OBD faults. The alignment of the OBD regulations and DTC assignment in systems with large numbers of similar/identical components is discussed, along with apparent conflicts between existing OBD regulations and the physical realities of battery systems in HEVs and PHEVs. Presenter Dyche Anderson, Ford Motor Co.

Plug-In Hybrid and Extended Range Electric Vehicle's have quickly become the focus of many OEM's and suppliers. Existing regulations and test procedures did not anticipate this rapid adoption of this new technology, resulting in many product development challenges. The lack of clear requirements is further complicated by CARBs consideration of CO2 inclusion in their next light duty OBD regulation. This presentation provides an overview of the regulatory requirements for OBD systems on hybrid vehicles that intend to certify in California. Near term challenges for EREV?s and PHEV?s are discussed, including concerns with the existing denominator and warm-up cycle calculations. Some proposals are made to address these concerns. Presenter Andrew Zettel, General Motors Company

OBD requirements for aftertreatment system components require monitoring of the individual system components. One such component can be an NH3-SCR catalyst for NOx reduction. An OBD method that has been suggested is to generate positive or negative spikes in the inlet NH3 concentration, and monitor the outlet NOx transient response. A slow response indicates that the catalyst is maintaining its NH3 storage capacity, and therefore it is probably not degraded. A fast response indicates the catalyst has lost NH3 storage capacity, and may be degraded. The purpose of the work performed at Southwest Research Institute was to assess this approach for feasibility, effectiveness and practicality. The presentation will describe the work performed, results obtained, and implications for applying this method in test laboratory and real-world situations. Presenter Gordon J. Bartley, Southwest Research Institute

This article characterizes the special features of drilling of CFRP/Titanium and -Aluminium stacks. Simplified theoretic models will show how CFRP/Titanium stacks should be machined without scratches and burn marks contacting carbon. Low axial forces and smart chip removal technology are the main characteristics of the drilling tool technology, optimized to reach H8 quality in one shot operation. Presenter Peter Mueller-Hummel, Cutting Tools Inc.

The aerospace industry has long sought a solution for storing maintenance history information directly on aircraft parts. In 2005 leading airframe manufacturers determined that passive Radio Frequency Identification (RFID) technology presented a unique opportunity to address this industry need. Through the efforts of the Air Transport Association (ATA) RFID on Parts Committee and SAE International testing standards and data specifications are in place to support the broad adoption of passive RFID for storing parts history information directly on aircraft parts. The primary focus of the paper will be on the SAE AS-5678 environmental testing standard for passive RFID tags intended for aircraft use. Detail will be provided to help aerospace manufacturers understand their role and responsibilities for current programs and understand how this may impact their parts certification process.

The increasing complexity of aerospace products and programs and the growing competitive pressure is facilitating the aggregation of small, medium and large enterprises of certain geographical regions into more integrated and collaborative entities (clusters). Clusters are by their same nature formed by heterogeneous companies, with huge differences not only in size but also for their core competences: such a diversity is a strength of the cluster, but it also increases its complexity. The purpose of this paper is to describe a benchmarking methodology that can be adopted to assess the performances of companies belonging to a cluster from different perspectives: economics and financials, competitive differentiators, specific know how, business strategies, production and logistic effectiveness, quality of core and supporting processes.

This presentation shows the SCADE System product line for systems modeling and generation based on the SysML standard and the Eclipse Papyrus open source technology. SCADE System has been developed in the framework of Listerel, a joint laboratory of Esterel Technologies, provider of the SCADE�, and CEA LIST, project leader of the Eclipse component, Papyrus. From an architecture point of view, the Esterel SCADE tools are built on top of the SCADE platform which includes both SCADE Suite�, a model-based development environment dedicated to critical software, and SCADE System enabling model-based system engineering. SCADE System includes Papyrus, an open source component (under EPL license), integrated in the modeling platform of Eclipse. Using this integrated modeling platform, both system and software teams share the same environment for system development. Furthermore, other model-based tools can be added to the environment, due to the use of Eclipse.

This talk will present an overview of the newly published DO-326/ED-202 "Airworthiness Security Process Specification". Presenter Daniel P. Johnson, Honeywell

The presentation provides an overview about the activities of Eurocae Working Group 72 (WG-72) starting with a brief synopsis of the context which suggested why such a committee should be established in 2006. It then goes into further detail about the drivers for the work of the committee, which call for the products to be delivered. It addresses some of the challenges with respect to its users. It points out that one of the lessons the committee learned was importance of the focus on the users, such that the products provide their maximum utility. Hence, the users should better be among the participants to achieve this objective. Other industries have dealt with the subject of Information System (or Cyber-Physical) Security long before this industry was forced to consider it. Consequently there are many industry standards and national or international norms, which may help to develop what is deemed needed for Civil Aviation.

A simulation framework with a validated system model capable of estimating fuel consumption is a valuable tool in analysis and design of the hybrid vehicles. In particular, the framework can be used for (1) benchmarking the fuel economy achievable from alternate hybrid powertrain technologies, (2) investigating sensitivity of fuel savings with respect to design parameters (for example, component sizing), and (3) evaluating the performance of various supervisory control algorithms for energy management. Presenter Chinmaya Patil, Eaton Corporation

The growing need for an efficient worldwide airspace system management, generated by an increasing traffic load, requires new capabilities for air-ground data communication technologies. In order to cope with these requirements, the Federal Aviation Administration (FAA), EUROCONTROL, and the International Civil Aviation Organization (ICAO) have jointly made specific recommendations for candidate technologies for the airport surface communication network. In the SESAR project, the Aeronautical Mobile Airport Communication System (AeroMACS) technology is being developed in such a way to provide next generation broadband and wireless data communications for airport surface applications (i.e. Air Traffic Control ? ATC, Airline Operational Communications ? AOC, and surface vehicles services).

A combination of laboratory reactor measurements and vehicle FTP testing has been combined to demonstrate a method for diagnosing the formation of NO2 from a diesel oxidation catalyst (DOC). Using small cores from a production DOC and simulated diesel exhaust, the laboratory reactor experiments are used to support a model for DOC chemical reaction kinetics. The model we propose shows that the ability to produce NO2 is chemically linked to the ability of the catalyst to oxidize hydrocarbon (HC). For thermally damaged DOCs, loss of the HC oxidation function is simultaneous with loss of the NO2 production function. Since HC oxidation is the source of heat generated in the DOC under regeneration conditions, we conclude that a diagnostic of the DOC exotherm is able to detect the failure of the DOC to produce NO2. Vehicle emissions data from a 6.6 L Duramax HD pick-up with DOC of various levels of thermal degradation is provided to support the diagnostic concept.

This presentation provides a overview of validating Time Triggered Ethernet (TTE) for use as the network to interconnect the avionics for manned Space Vehicle. The next manned Space Vehicle will use Time Triggered-Gigabit Ethernet (TT-GbE) leveraged from commercial development of TTE critical Intellectual Property. There are several validation considerations of either separating TTE segments or adding new TTE segments onto the network caused by the different phases of a manned space vehicle from pre-launch to re-entry. Considerable amount of validation testing has been successfully performed on TT-GbE/TTE. Presenter Victor Revelle, Honeywell International Inc.

Revisions to the California OBD-II diesel regulations required many updates to various SAE and ISO on-board diagnostic standards; these include major revisions to SAE J1979, J1699-3, J2012 and J1930. This presentation is intended to review the background for these changes as well as the revisions made in these documents. Presenter Robert Gruszczynski, Volkswagen of America

The OBD approval process can be a frustrating time for both manufacturer and ARB staff. For manufacturers, a long approval process can sometimes mean accepting deficiencies prematurely in exchange for an approval. For ARB staff, they are inundated with highly technical information which they must review, garner understanding of and then apply their experience to evaluate it for compliance. OBD approval anxiety can be minimized, if not avoided, when manufacturers understand ARB�s expectations. This presentation will take you through some unwritten rules and common pitfalls which can impede the approval process, thus providing a guideline to a less painful and more efficient certification document review and approval. Presenter Mark Frank, Winterpark Engineering Llc

In recent years, all major microprocessor manufacturers are transitioning towards the deploymenet of multiple processing cores on every chip. These multi-core architectures represent the industry consensus regarding the most effective utilization of available silicon resources to satisfy growing demands for processing and memory capacities. Porting off-the-shelf software capabilities to multi-core architectures often requires significant changes to data structures and algorithms. When developing new software capabilities specifically for deployment on SMP architectures, software engineers are required to address specific multi-core programming issues, and in the ideal, must do so in ways that are generic to many different multi-core target platforms. This talk provides an overview of the special considerations that must be addressed by software engineers targeting multi-core platforms and describes how the Java language facilitates solutions to these special challenges.

The development and release process for Cummins first US HD OBD certified product encountered numerous hurdles. Beyond the purely "technical" difficulties, there were also challenges related to our product development processes. This presentation provides recommendations for HD OBD product development processes & improvements. Topics will include: Training needs for program management, Performance tuning strategies vs. OBD needs, Planning for post-certification product changes, etc. Presenter Greg Moore, Cummins Inc.

This paper presents an extension of our earlier work on Cummins Vehicle Mission Simulation (VMS) software. Previously, we presented VMS as a Windows based analysis tool to simulate vehicle missions quickly and to gauge, communicate, and improve the value proposition of Cummins engines to customers. Presenter Nagesh Belludi, Cummins Inc.